Forum Post: PowerConnect 5424 MAC based VLAN assignment
7 for iSCSI. If I configure the port on the switch for my LAN VLAN, obviously I can get to the management IPs, and obviously, the Compellent would not be able to contact the iSCSI VLAN on that port (If...
View ArticleForum Post: RE: PowerConnect 5424 MAC based VLAN assignment
What commands were you seeing? The one that I can think of MAC authentication bypass which can put a port into a vlan but the whole port goes into that VLAN.
View ArticleForum Post: 2 FN410T in FX2 in VLT-Mode
we have a FX2 with 2 FN410T as IOMs. I changed the mode from Standalone to VLT and I'm not sure if this works correctly. I did it strongly like advised in the Deployment-Guide found here:
View ArticleForum Post: RE: Settings Jumbo frame on N4064F with mixed port settings
Thanks for the answer Yes
View ArticleForum Post: What is the best practice N4064F for setting lacp lagg Hash...
Hello, I need to set port channel lacp lagg for use with nfs protocol , the switch type is N4064F Under LAG Hash Configuration there are several option as shown in attached image , My question is what...
View ArticleForum Post: RE: 2 FN410T in FX2 in VLT-Mode
"The delay-restore feature waits for all saved Configurations to be applied, then starts a Configurable timer. After the timer expires, the VLT ports are enabled one-by-one in a controlled manner.
View ArticleForum Post: RE: What is the best practice N4064F for setting lacp lagg Hash...
In most situations the Enhanced Mode provides good performance. I suggest testing the environment with the Enhanced Mode. What device is your NFS volume on? How many links in the LAG? I can help do...
View ArticleForum Post: RE: 2 FN410T in FX2 in VLT-Mode
Yes, I expected the backup-link to be the Management-IP. And I configured one on each of the IOM. And they are both pingable by each other. Than I used the VLT-Mode wich is kinda autoconfiguration. The...
View ArticleForum Post: RE: How delete port Channel interface on Dell N3024
I had the same problem with a PowerConnect 6224. But, clearing all settings from a port-channel will delete it from running config output. Besides, no physical port is to be attached to it. I did that...
View ArticleForum Post: RE: 2 FN410T in FX2 in VLT-Mode
The service should not be interrupted when just one switch is down. When you said the connection to the server was lost for a minute, I thought you meant the connection to the switch that was reloaded.
View ArticleForum Post: RE: 2 FN410T in FX2 in VLT-Mode
Aug 25 03:49:03: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Te 0/9 Aug 25 03:49:03: %STKUNIT0-M:CP %IFMGR-5-OSTATE_DN: Changed interface state to down: Po 127 Aug 25 03:49:04:...
View ArticleForum Post: RE: What is the best practice N4064F for setting lacp lagg Hash...
NFS will be used to spin on virtual guest with Xenservers , on the storage Freenas (ZFS) side we will have 3 x10G , and each hypervisor will have 2x10G per LAG , in addition will be configured to use...
View ArticleForum Post: RE: 2 FN410T in FX2 in VLT-Mode
I suggest getting the backup destination set correctly. Perhaps reduce the timer to 30 or 60 seconds. Look through that best practice list for any other tweaks that can be made. Then test again,...
View ArticleForum Post: RE: What is the best practice N4064F for setting lacp lagg Hash...
Looking through documentation such as: httpbit.ly/2gbzKUY Does not seem to indicate a preferred hashing algorithm. I suggest proceeding with testing with the default settings.
View ArticleForum Post: RE: 2 FN410T in FX2 in VLT-Mode
Hi, thx for your suggestions. But I cannot Change to the vlt-mode. I showed you all comands I can issue in EXEC and conf-mode. But no VLT. And RSPT is not enabled in the Moment. Thx and regards
View ArticleForum Post: step by step switch setup for 10 times Dell X1018P to be used for...
Hi can anyone please provide me with a step by step process of how to setup the Dell X1018P i have 10 of these switches that need to be connected all with daisy chain topology. (Cat 6 cable) Also...
View ArticleForum Post: RE: step by step switch setup for 10 times Dell X1018P to be used...
In the Manuals sections there is a getting started guide that will take you step by step on the initial setup of the switch. You can then utilize the user guide to configure additional features. If you...
View ArticleForum Post: RE: Not able to ping default gateway from blade server
What device is the default gateway? Does it reside in the same VLAN as the servers? Are the servers able to communicate with other devices attached to the Cisco switch? Other devices in other VLANs? Is...
View ArticleForum Post: RE: Not able to ping default gateway from blade server
Dear Daniel, Please find the below info What device is the default gateway? Default gateway- Cisco Core Switch. Does it reside in the same VLAN as the servers? Yes it is reside in Same VLAN Yes other...
View Article