Forum Post: RE: Not able to ping default gateway from blade server
It sounds like the configuration of the switches are correct, but please feel free to post them up for review. Have you double checked the IP configuration to ensure the servers are in the same subnet...
View ArticleForum Post: Configuring RSPAN span/mirror port to see all vlan traffic in...
I am working on installing a trial Websense/Forcepoint installed in Hyper-V Windows 2012R R2. I am not able to get the server to see other VLAN LAN segment traffic. At this point I have configured the...
View ArticleForum Post: RE: Not able to ping default gateway from blade server
sh run Current Configuration ... ! Version 9.11(0.0) ! Last configuration change at Sat Apr 22 12:58:36 2017 by root ! Startup-config last updated at Sat Apr 22 13:07:01 2017 by root ! boot system...
View ArticleForum Post: RE: step by step switch setup for 10 times Dell X1018P to be used...
Thank you . i think my problem is more related to setting up LAG the correct way , i will have a look at the user guide.
View ArticleForum Post: RE: step by step switch setup for 10 times Dell X1018P to be used...
Here is a KB article to help guide you through the creation of Link Aggregation. httpdell.to/2veYuiO Let me know if you have any questions about the process.
View ArticleForum Post: RE: Not able to ping default gateway from blade server
Based on this information, it would appear that the issue is that VLAN 1 is not configured to cross port-channel 110. We need to go into VLAN 1 interface and add port-channel 110.
View ArticleForum Post: RE: Not able to ping default gateway from blade server
Dear Daniel. I m getting below error. Dell(conf)#interface port-channel 110 Dell(conf-if-po-110)#portmode hybrid % Error: Port is in Layer-2 mode Po 110. And regarding VLAN 1., you want me tagged or...
View ArticleForum Post: RE: Not able to ping default gateway from blade server
You will need to issue the no switchport command first, then the hybrid command, then add back in the switchport command. httpdell.to/2i2lrTh VLAN 1 should match the Cisco side, which should be...
View ArticleForum Post: RE: Configuring RSPAN span/mirror port to see all vlan traffic in...
When configuring RSPAN, you will have a designated RSPAN VLAN, this RSPAN VLAN is where the mirrored traffic is flooded to. All switches that will be the source, destination, or a switch transmitting...
View ArticleForum Post: RE: 2 FN410T in FX2 in VLT-Mode
suggest you change to full switch mode then manual configured VLT setting as you want.
View ArticleForum Post: Dell X1052P Switches & Dell TZ300
I have a dell TZ600 sonicwall and 4 Dell x1052P switches in different NOC rooms. 2 in NOC-A, 1 in NOC-B and another in NOC-C. The two in NOC-A are connected by 10GBe connection and the others are 2 X...
View ArticleForum Post: RE: Dell X1052P Switches & Dell TZ300
Please ignore my subject line - it is a Sonicwall TZ600 and not a TZ300. The main problem is with the switches.
View ArticleForum Post: Dell X1052P Firmware Upgrade - Console Putty Issue
I want to upgrade the firmware on the x1052P switches and read it needs to be done in CLI. However whenever I connect the cable and use PUTTY - PUTTY just dings and I click Open. Using a windows 7...
View ArticleForum Post: RE: Dell X1052P Switches & Dell TZ300
Turns out the problem port was in a LAG which was set as a truck which all 4 VLANs. It is not apparent in the VLAN settings except when you view the tagging the port in question is not tagged at all....
View ArticleForum Post: RE: Dell X1052P Firmware Upgrade - Console Putty Issue
Have you tried uninstalling and reinstalling the driver? The PDF that comes with the driver has instructions on how to do this. It sounds like you have followed the instructions listed in the KB...
View ArticleForum Post: RE: Dell X1052P Firmware Upgrade - Console Putty Issue
Daniel - yes - connection is to the micros USB on the back of the switch. I'll try the uninstall - install document tomorrow. Thanks.
View ArticleForum Post: 5548 Remove Switch from Stack
I removed spanning-tree on all the ports on switch 3. Then I moved around the HDMI interconnect cables so that only switch 1 and switch 2 are interconnected.
View ArticleForum Post: RE: 5548 Remove Switch from Stack
It sounds like the stack needs to be reloaded. During startup the switch will go through and detect the stack members. You could try to issue the command to reload just stack member 3, and since it is...
View ArticleForum Post: RE: 5548 Remove Switch from Stack
Tried reload: stack22# reload slot 3 Unit does not exist over the stack! The firmware was a little old (4.1.0.16), so I did update it. But that did not help.
View ArticleForum Post: RE: Setting vlan MTUs on x1052
Is there a reason I cannot enable jumbo frames on this very screen? The option enable is missing entirely along with the radio button to select.
View Article