Forum Post: RE: VRTX R1-2401 switch 1.0.0.63 frimware request
please check below information from "R1-2401 VRTX 1GbE Software Upgrade Instructions (Ver 1.xx to 2.xx).pdf" in r2401-20057 firmware zip file. So I need 1.0.0.63 release. >>>>> NOTE: The...
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
hi, I did it with the console cable and no issue, everything works fine ! Thanks at all,
View ArticleForum Post: RE: VRTX R1-2401 switch 1.0.0.63 frimware request
Thanks for pointing that out, I had not seen this information. There is a folder included in the latest firmware downloaded labeled Interim Version, you will find 1.0.0.63 in that folder.
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
Excellent! glad to hear that worked. Cheers
View ArticleForum Post: VLAN Setup / Dell PowerConnect 2816 and 2824
I am trying to set up two VLANS on the PowerConnect 2816 (in test mode) and eventually on the 2824. Although I have read the manual carefully, I'm having a bit of a disconnect between how I associate a...
View ArticleForum Post: RE: PC8024F
username "admin" password ac09c5045f45c8fd3c125f0b3b742e4b privilege 15 encrypted username "rancidPoll" password 1b430c6g7deb13487f016d09e7c66fce privilege 15 encrypted ip ssh server
View ArticleForum Post: RE: PC8024F
It appears that the enable password line is still present. When you run the no enable command does the switch return any error messages? Or anything recorded in the logs? As a side not, that firmware...
View ArticleForum Post: RE: PC8024F
Yes, still present because i re-add it in the config file to allow remote ssh enable session. if i configure no enable password. when i use SSH to remotely connect to the switch, the message is :...
View ArticleForum Post: RE: PC8024F
Sorry, I do not have any experience with rancid clogin scripts.
View ArticleForum Post: RE: VLAN Setup / Dell PowerConnect 2816 and 2824
In most cases, a VLAN will have a different subnet from other VLANs. If these two VLANs will always be separate and never route between each other, then you could have the subnet in each. Do both VLANs...
View ArticleForum Post: FTOS 8.3.2.0 download?
I need an old version of FTOS. 8.3.2.0 Is still there anyplace online to download the .bin file??
View ArticleForum Post: RE: VRTX R1-2401 switch 1.0.0.63 frimware request
got it , many thanks. Surprise
View ArticleForum Post: RE: n2000 interoperability with 55xx series
It is usually recommended to stay up to date on firmware releases, but there is no minimum level requirement.
View ArticleForum Post: VLANs not routing
Hi, I was hoping to get VLAN 3 "Phone-VLAN" to be able to have internet access, I have a PhoneSystem on 10.10.3.1 which can ping the IP address of each VLAN and also the DHCP server 10.0.1.14 but not...
View ArticleForum Post: RE: VLAN Setup / Dell PowerConnect 2816 and 2824
Based on the hardware being used, and the need for everything to be on the same subnet, VLANs are not going to be a practical solution. I would set the priority higher for the interfaces with phones,...
View ArticleForum Post: RE: VLAN Setup / Dell PowerConnect 2816 and 2824
Daniel, thank you for your expertise and guidance. Is this the correct setting for the ports that have voice? I have not made any other changes to the switch. We do have a firewall, but no Layer 3...
View ArticleForum Post: RE: Problem with the port for the iSCSI on M8024-K / M6348
1. No, all the servers in your shopping cart. 2. On any file. 3. Normal copying to other servers is normal, and then if you connect to a 1 GB network, the speed of the full use (97% of the network and...
View ArticleForum Post: s3048-on lag (link aggregation) only gets full bandwidth one way
The environment have two servers connected to the switch (Dell s3048-on) ServerA - 10Gbps link (TenGigabitEthernet 1/49) ServerB - 4 x 1Gbps link (GigabitEthernet 1/1-1/4) The purpose is to have...
View Article