Forum Post: RE: FORCE10 MXL configuration issue
Hi Farhan Ashraf, Do you settle this case? Can you share something from your configuration? I have some issue with FCoE with Mxl/Brocade 300 too. Sometimes, the server's CNA can not log in to the...
View ArticleForum Post: PC8024F
After setting no enable password on my PC8024F , firmware 5.1.1.7, when i'm connected by SSH on it, i cannot enable it with success, i have the authentication failed error.... Do you have any ideas ?...
View ArticleForum Post: MXL-10/40GbE Management Interface
This is normal because my new MNGT vlan have a TAG and so i would like to link the ethernet management 0/0 interface of each MXL to an access port in the new MNGT vlan. The question is how to find the...
View ArticleForum Post: RE: PC62xx - private vlans / protected ports
A VLAN is by default a layer 2 broadcast domain. You can think of it as a room with locked doors, the people inside the room are only able to talk to one another. As soon as a device on the network has...
View ArticleForum Post: RE: Configuring a 3524 switch in an existing network
Any of the 24 ports can be used to connect the 3524 to the 3com. Since this is a flat network, no additional VLANs, you should have no issues simply migrating the connections over. The switch supports...
View ArticleForum Post: RE: PC8024F
Can you post up the current configuration? We can help look through it for any suggested changes.
View ArticleForum Post: RE: PC8024F
not now, i'll go on site tomorrow to edit the configuration with a console cable:Ss
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
The management interface is an OOB interface which connects through the chassis CMC. Traffic on this port is segregated from operational network traffic on the switch ports and cannot be switched or...
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
Ok thanks for your reply. So, if i understand, the management ethernet 0/0 of each MXL switch is using the CMC Gb1 / Gb2 of the chassis. My topology is as below: CMC M1000E IDRAC IP...
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
Yes, you should be able to make that IP Address assignment. GB2 of the CMC is used only for daisy chaining Enclosures, not for connections to switches. GB1 of the CMC is what will carry to management...
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
Ok perfect, many thanks, i'll try it on tomorrow and keep you informed.
View ArticleForum Post: RE: PC62xx - private vlans / protected ports
I understand the concepts. I only needed to be sure is that PC62xx VLAN(no L3) cannot leak traffic to/from other VLANs, stays isolated as long as no IP/routeing. Definition of "private" on these...
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
I forgot, one last question I have 2 M820 blades in this chassis, i think, it's the same ? IDRAC of the blades M820 is going through GB1 ?
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
That is correct, iDRAC traffic uses that interface as well.
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
ok thanks and so as i changed the IDRac IP Address of the GB1 M1000e i lost the connectivity to my M820 blades How is it possible to configure the M820 iDRAC ip address on M820 by using a console cable...
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
While making changes like these, a serial connection will probably be the best solution. httpdell.to/2neBMVX
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
$ getniccfg -m switch-1 DHCP Enabled = 0 IP Address = 10.150.0.25 Subnet Mask = 255.255.255.0 Gateway = 10.150.0.254 $ getniccfg -m switch-2 DHCP Enabled = 0 IP Address = 10.59.200.6 Subnet Mask =...
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
I am not sure why it is only taking the first one. Are there any messages logged on the switches? Perhaps try making these changes why on the switch CLI? http://dell.to/2nW7mEY
View ArticleForum Post: RE: MXL-10/40GbE Management Interface
nope, no error and as i managed to be able to reach the CMC1000e iDrac by web, i tried it by using the web interface and idrac told me that it'll take a moment.. don't know why,,, maybe a propagation...
View ArticleForum Post: RE: Schedule script to automatically execute on N-Series switches?
I think this is possible using Python scripting. You may want to check into the "Python Scripting for Dell Networking N-Series" deployment guide:...
View Article
