Forum Post: Force10 MXL 10/40gb Firmware Update
I purchased 2 Dell Force10 MXL 10/40gb switches from a 3rd party reseller in Dallas, Tx. I am trying to update their firmware to at least match the other 2 I have which is on version 9.3 FTOS.
View ArticleForum Post: RE: Locked out of Switch
Hi, You can reset the switch by changing to unmanaged mode and back. Page 23
View ArticleForum Post: RE: Locked out of Switch
Okay, I'll try that, but it has not moved out of managed mode. I held down the button until the port lights flashed and the manage mode LED started to flash, but it went back to manage mode. I then...
View ArticleForum Post: RE: Locked out of Switch
the managed mode LED flashes for about 12 seconds then ALL LEDs (so all the RJ45 ports) flash on/off, there's a 2 second pause and then it goes through the same cycle again".
View ArticleForum Post: RE: Locked out of Switch
Well, that is a problem because none of the ports are on VLAN1. With no ports on VLAN1, what can I do to reset it?
View ArticleForum Post: RE: Locked out of Switch
If the reset with switching to unmanaged does not work you can connect with the terminal and erase the flash file.
View ArticleForum Post: RE: Locked out of Switch
I was hoping there would be something else because the 2808 does not have the terminal option, only the 2816 and higher. Unless I am missing something? Thanks for the help and I will respond to this...
View ArticleForum Post: RE: Locked out of Switch
I was unable to connect to the switch this morning by switching it over to unmanage and then back to manage. However, the user manual does not explain how to connect to the 2808 via terminal, since...
View ArticleForum Post: RE: Locked out of Switch
I went back and forth between the modes a few times before I was able to get in. Not only did I change all of the ports into different VLANs, but I also changed the IP address to the switch.
View ArticleForum Post: RE: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2...
The LM throughput avg. 500-700Mbps only. 6Gbps LACP team using (6) NICs from each R710, no weighting set on hyper-V vSwitch either yet. Examining the Team network stats on each server 1 phy NIC on each...
View ArticleForum Post: RE: Reset password on stacked 8164
The next night after posting, the switch primary switch (that we hadn't rebooted) had some type of issue, and failed. I think it rebooted. Unfortunately, someone had turned off the logging, so I don't...
View ArticleForum Post: RE: Reset password on stacked 8164
Great info, thanks for letting us know how you were able to gain access again. Be sure to turn logging back on, in case the switch goes down again. Cheers
View ArticleForum Post: RE: Reset password on stacked 8164
Yep, we turned logging back on right after setting up the AAA. :)
View ArticleForum Post: RE: N3048 cannot exit ssh sessions with firmware 6.3.0.3
Wanted to chime back in and let everyone know that the newest 6.3 firmware release is now out for download. The release notes show all of the improvements made, including resolving the SSH behavior...
View ArticleForum Post: S4048 FTOS SAN Failure
Our shop has recently migrated over to two Force10 S4048 switches into our Compellent SAN environment. Both switches are 48 port 10GB. Our SAN has three physical servers that all connect up to the two...
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
Also thought I should mention the stacking setup. 1xg1 > 2xg1, 1xg2 > 3xg1, 2xg2 > 3xg2
View ArticleForum Post: RE: S4048 FTOS SAN Failure
My apologies it looks like I posted this on the wrong forum.
View ArticleForum Post: Dell N2048 Half duplex not possible.
I Have a Cisco ATA186 connected to a Dell N2048 with firmware 6.2.7.2 I´ve forced the port to 10Mbit, and trying to set half-duplex - but it´s not possible.. Is half-duplex no-go on the Dell N2000...
View ArticleForum Post: RE: Dell N2048 Half duplex not possible.
hmm.. N2000 Doesnt support half-dup..
View Article