Forum Post: RE: Latency/Drops on a Dell Stack - One switch Only
That should eliminate an issue with the hardware, unless it is a cabling issue. Does the switch have latency if the connections are made and it is not part of the stack?
View ArticleForum Post: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2 vNICs
Setting up new R710 servers to upgrade existing 2008R2 Hyper-V to a 2012R2 Hyper-V and current network was inherited and is very basic and all physical using default layer 2 switch VLAN (1), no vSwitch...
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
i have not checked that, is there a way to diagnose a cabling issue within the GUI?
View ArticleForum Post: RE: Firmware issue on Dell N4032F
Thanks for the information regarding software release, I'll try to rollback during maintenance window. Do you know is there any plans to add this ospf feature to DNOS 6?
View ArticleForum Post: RE: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2...
Pics didn't post of configs, reposting them.
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
yes, page 26 NOTE: You can also run a cable test using the Web Interface. In the navigation tree, click System > Diagnostics.
View ArticleForum Post: RE: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2...
Hi, Do the VMs communicate with each other? Can the switch communicate with them if they are not teamed? Can the host ping the switch?
View ArticleForum Post: RE: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2...
Only have 1 test vm on the new host and as stated its on the native VLAN (1) and can communicate to all other vm's in production and test. Not quite understanding the team question, native VLAN is...
View ArticleForum Post: RE: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2...
If you do a tracert where do the pings stop?
View ArticleForum Post: RE: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2...
Both can ping each other fine now. I just have to get the 2nd upgrade server back online, got locked out after I created a vNIC and it wiped out the pNIC IP :-(. That will validate host to host comms....
View ArticleForum Post: RE: Firmware issue on Dell N4032F
I am currently not aware of the feature being on any road map to be added.
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
Says "error! Invalid interface to perform test." I am trying to test the stacking port interfaces.
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
Here is a backup of a known "good" startup config. It defers from my current startup config somehow. I notice several differences in fact. Specifcally the "bridge aging-time 1230" shows up on my...
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
Is there an easy way for me to load this backup startup config to my setup?
View ArticleForum Post: RE: Configuring VLANS Using PowerConnect 5448 & Hyper-V 2012 R2...
The other VLAN settings do look correct.
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
Is it a backup config file on the switch or just a copy that you have?
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
i have copies of the startup and running config saved as a text file on a tftp server
View ArticleForum Post: RE: Latency/Drops on a Dell Stack - One switch Only
In that case, copying and pasting the config from a terminal session would work, and then copy running config to startup but it might be easier just to make the changes between the configs, depending...
View ArticleForum Post: RE: Dell n2048 - MMU MTRO PAR generic parity error
A simple reload has resolved the log entries for us, but was a slightly different error.
View ArticleForum Post: Locked out of Switch
I was trying to create a test network with the 2808 to a router. I put all ports into a VLAN and now I am unable to connect to it either directly or through the router. I was wondering if I could...
View Article