Forum Post: IP configuration assistance on PowerConnect 6248
I inherited a pair of stacked PC 6248 switches. These two switches are active and in production. I am not near these switches as there are located in another state at one of our other company locations.
View ArticleForum Post: RE: Open Manage Network Manager
Thanks for those screen shots. You are spot on, the first screen shot is values from sflow sampling. The second screenshot is then the total calculated from the sampling statistics. I believe you can...
View ArticleForum Post: RE: Open Manage Network Manager
What I have done is unregister my 4 switches from Traffic flow. I then saw that there was no traffic to display in Traffic flow as expected. I then registered one of my cores and the data started to...
View ArticleForum Post: RE: IP configuration assistance on PowerConnect 6248
- The management VLAN on the 6200 switches is not routable. It is intended to be used as a form of OOB management. This would be why clients on VLAN 10 cannot access VLAN 1. There are two options here.
View ArticleForum Post: RE: Copying configuration via SFTP on N-Series 3048P or 4032F
There is no error message using scp as opposed to sftp. Identical md5sum on files both ways (scp and sftp). sftp error occurs with startup and running config. Happens on 3000 and 4000 series. I note it...
View ArticleForum Post: RE: Open Manage Network Manager
I am not certain why the one site is seeing traffic for switches on the other site, unless this traffic has a destination at the site with sflow enabled on it. How do the two sites connect with one...
View ArticleForum Post: RE: VLANs can't see internet
Thank you Daniel. its been a busy week. I will try these steps tomorrow and let you know how it goes. I appreciate all you help stay tuned
View ArticleForum Post: RE: VLANs can't see internet
Daniel, Thank you for your patience while I try to wrap my brain around this... I started entering in your suggested commands and the CLI. once I got to this line and entered the command. I lost all...
View ArticleForum Post: RE: Failed to acquire an IP address on Vl1; DHCP Server did not...
D BLOCK WL>en D BLOCK WL#show running-config !Current Configuration: !System Description "Dell Networking N2024P, 6.3.1.8, Linux 3.6.5-7dc37651" !System Software Version 6.3.1.8 !
View ArticleForum Post: RE: Open Manage Network Manager
The link between the 2 sites is a 1GB leased line that is setup as a trunk. Open Manage lives on site B. I have sflow configured on Site B core. I have just found a couple of switches on Site A that...
View ArticleForum Post: RE: VLANs can't see internet
I apologize, I should have been a little clearer when I suggested to make these changes from console. Here is an example config you can start with. I always like to take the approach of configuring the...
View ArticleForum Post: RE: is my X1052P switch bricked?
Me too, any workaround? I have upgraded boot code to 1.0.0.21. and it bricked when i upgrade the firmware to 3.0.0.82.
View ArticleForum Post: RE: Open Manage Network Manager
Let's say I want to look at the stats of a specific interface on a switch. In the past, I would just use show interface status on Cisco and it would show the load i.e. 120/255, 200/255 so I could...
View ArticleForum Post: RE: is my X1052P switch bricked?
did not know 3.0.0.82 is out, my contact Dell told me they wanted me to try 3.0.0.81 firmware and I have updated about six switches so far with no issues yet.
View ArticleForum Post: RE: is my X1052P switch bricked?
I upgraded my X1026P to .81 without issue. I have ONLY been updating them via the console and TFTP. I don't trust the web interface. I hasn't seen that .82 was released. I also always update the...
View ArticleForum Post: RE: Failed to acquire an IP address on Vl1; DHCP Server did not...
D BLOCK WL>en D BLOCK WL#configure D BLOCK WL(config)#interface vlan 1 D BLOCK WL(config-if-vlan1)#no ip address dhcp ^ Invalid IP address. IP address should be in a.b.c.d format where range for a,...
View ArticleForum Post: RE: Open Manage Network Manager
Hi Daniel That is really useful. I just need to tweak these reports. This software is like a maze to operate with. cheers
View ArticleForum Post: No lights on the ports m6220
I have a Dell m1000e chasis and a1/a2 has poweconnect m6220s. The internal ports 1-16 works and active. But when I plugged the cable on port 17-20 there is not light and show interfaces status says...
View ArticleForum Post: RE: No lights on the ports m6220
Hi The other end is connected to the patch panel port which i have verified to be working. Yes the no shut has been executed. Thanks Paras
View ArticleForum Post: RE: No lights on the ports m6220
Is the switch firmware up to date? This is occurring on both switches? Are they stacked? Have you rebooted the switch?
View Article