Forum Post: RE: m6220/m1000E: How to create sub-net for each blade?
The M6220 connects to the internet via 10.10.10.1 (example IP) gateway. Our provider hosts this gateway. These IP addresses are being assigned to servers (blades). What we are trying to do is subnet...
View ArticleForum Post: RE: m6220/m1000E: How to create sub-net for each blade?
It looks like the switch supports private VLANs. This may be an option for you, allowing those devices to be in the same VLAN, but not be able to communicate with each other. The user guide has some...
View ArticleForum Post: RE: PowerConnect 3424
Me podrÃan decir como dejo un switch powerconnect 3424 y 6224 en estado de fabrica por favor, el problema es que no me puedo conectar por consola tengo un db9 un cable de consola y un serial a usb pero...
View ArticleForum Post: Force10 to Cisco
I have a couple Force10 4810P switches I want to connect to a set of stacked Cisco 3750s. I'm a complete novice on the Force10's so configuring them properly is proving to be troublesome. Does anyone...
View ArticleForum Post: PowerConnect 2848 set Qos for Voip vlan
Hi, have a PowerConnect 2848 and have set up a vlan for my phones. not sure how to set the QoS for the phones vlan.
View ArticleForum Post: Dell N2000 series stacking
I have unit 4 units n2048p stacking together as shown, can I force switch 1 become permanent master/management unit? Currently I only can renumber the unit ID. Firmware ver. 6.3.1.8 Additional...
View ArticleForum Post: RE: PowerConnect 2848 set Qos for Voip vlan
Can any one tell me if I just set the port the phone's are on QoS to 5 and leave the rest default will work ?
View ArticleForum Post: Copying configuration via SFTP on N-Series 3048P or 4032F
Testing (firmware 6.3.1.8) copy startup-config suser@hostfilename executes but always ends with File transfer failed! But a check of destination host shows the file always transfers (I assume in its...
View ArticleForum Post: RE: VLANs can't see internet
- The gloabl ip address command assigns an IP address to the management VLAN, which by default is VLAN 1. On the 6200 switches, the management VLAN is not routable. It is intended to use this VLAN as a...
View ArticleForum Post: RE: Dell N2000 series stacking
During initial setup, you can control which switch is the master by turning on the master switch first. But if the stack is already established, and you want to change which switch is the master, you...
View ArticleForum Post: RE: PowerConnect 2848 set Qos for Voip vlan
The user guide has information on what all the different settings are for. Page 146 begins the chapter on QoS. httpdell.to/28JdImh Here are the steps I would start with. - Make sure CoS is enabled....
View ArticleForum Post: RE: Oversized package
Is jumbo frames enabled on the switch? Have you done any packet captures to see what size these frames actually are? What firmware is the switch on?
View ArticleForum Post: RE: VLANs can't see internet
I took the 3424 out of the mix and plugged the internet connection directly in to port 2 on the 6224. But, I still can't get to the internet from a machine plugged in to vlan 10 or vlan 20... -Michael
View ArticleForum Post: RE: PowerConnect 2848 set Qos for Voip vlan
Thanks for both of your reply to my both of my post. Have some other questions if you don't mind. This is a Vlan question should ports be Taged or untagged and what's F stand for ?
View ArticleForum Post: RE: VLANs can't see internet
If you want VLAN 1 to be routed you will need to make another VLAN and assign it to be the management VLAN. Then assign 192.168.1.3 to VLAN 1 interface.
View ArticleForum Post: RE: PowerConnect 2848 set Qos for Voip vlan
If the phones have workstations plugged into them, then the phones will be tagged, and the workstation VLAN would be untagged. If there are no workstations plugged into them, then you could really use...
View ArticleForum Post: X4012 - showing two default gateways?
OK, I have a pair of X4012 switches installed in a remote location. When I had configured them, I had originally set the default-gateway to an atypical value because I thought I was going to be sharing...
View ArticleForum Post: RE: PowerConnect 2848 set Qos for Voip vlan
Thanks for info! I'm new to this obviously and the manual is not very clear on things.
View ArticleForum Post: 40 port card throughput on E600 ExaScale chassis
Anyone using 40 port 10G cards (LC-EJ-10G-40S) with the E600i ExaScale platform ? What's the per port throughput on these cards ? Per docs each slot should have 100G of capacity but how does this map...
View ArticleForum Post: RE: X4012 - showing two default gateways?
To remove the default gateway you will need to put no in front of the command. Example: console(config)# no ip default-gateway 10.10.10.1
View Article