Forum Post: RE: FORCE10 MXL configuration issue
Hi Daniel So we are synced up now as u got the exact scenario here now in this case what Commands and configuration we need on our Foce10 MXL so i can see my servers's WWN on Brocade 300 switch.
View ArticleForum Post: RE: SSH unreachable and CONSOLE password lost on a PowerConnect...
Hi, Thanks a lot, it worked perfectly ! Regards,
View ArticleForum Post: RE: FORCE10 MXL configuration issue
The rest of the configuration is still valid. FIP snooping should still be enabled. The server facing ports should be configured the same. The only change is that the FC ports will default to NPIV and...
View ArticleForum Post: RE: Dell N4000 - soc_xgs3_mem_dma: FP_TCAM.ipipe0 failed(NAK)
We would want to figure out which switch was causing the memory errors. Most likely that switch needs to be replaced. Are the switches under warranty?
View ArticleForum Post: RE: Problem settings up VLANs on PowerConnect 2724
Is the DHCP server in VLAN 101, or some other VLAN? If it is in a different VLAN, do one of the switches have DHCP relay configured? What switch is the DHCP server plugged into?
View ArticleForum Post: RE: Dell N4000 - soc_xgs3_mem_dma: FP_TCAM.ipipe0 failed(NAK)
Yes , the switch should but first , how can we know which switch is memory error ?
View ArticleForum Post: RE: Problem settings up VLANs on PowerConnect 2724
The DHCP server is on the router on the 2724. It "should" be on all the VLAN interfaces. Now that i have reset it and using VLAN as the primary as 1 it seems to be fine. (Basically 5324 101 -> 2324...
View ArticleForum Post: PC 6224 is killing my network. Help? :)
I have a PowerConnect 6224 that I'm using at home on my home network. I recently started having a really *** internet connection with Pings in the multi-hundred range. My setup is very simple:
View ArticleForum Post: RE: FORCE10 MXL configuration issue
Hi Daniel Thanks for the infoi will be really thankful if u again give me the exact commands step by step for this Looking forward for ur kind response. Regards Farhan
View ArticleForum Post: RE: Problem settings up VLANs on PowerConnect 2724
Glad to hear DHCP is working for the untagged VLAN now. It sounds like perhaps there was something no correctly configured on the 2724. It is hard to tell exactly what that could of been without seeing...
View ArticleForum Post: Force10 MXL 10/40 in M1000e - DCBX issue.
I require the use of dcbx with my M1000e as I have an internal M4110s Equallogics, and am using an ESXi cluster to access it. This has not been a problem in the pas, but right now it is a real issue.
View ArticleForum Post: RE: PC 6224 is killing my network. Help? :)
The switch should not need to be rebooted on a regular basis. The most common times for a reboot is when performing firmware updates. The latest firmware being 3.3.15.1. http://dell.to/2c7auvh While...
View ArticleForum Post: RE: FORCE10 MXL configuration issue
Sure thing, here is an example of the commands for setting up the switch with the FC module. The setup is a little different than the other commands we went over.
View ArticleForum Post: RE: Force10 MXL 10/40 in M1000e - DCBX issue.
I asked a technician to look at the MXL configuration with DCB and as confirmed that the important part is that PFC and ETS settings are correct. For him the configuration is working fine.
View ArticleForum Post: RE: Dell N4000 - soc_xgs3_mem_dma: FP_TCAM.ipipe0 failed(NAK)
The best way would be to unstack them and run them separately and see which one continues to give errors.
View ArticleForum Post: RE: N3024
Is the switch acting as the DHCP server? Or is there a separate device in this role? if the switch is operating as the DHCP server, a good place to start is with these show commands. # show ip dhcp...
View ArticleForum Post: RE: Force10 MXL 10/40 in M1000e - DCBX issue.
Thanks for keeping us posted on outcome. Glad to hear you were able to get some confirmation and that this is working correctly. Cheers
View ArticleForum Post: RE: How do you turn off PowerConnect 7048 fan speed warnings?
changing the logging to 4 quieted the switches email's down. we also tried a couple of other lines snmp-server filter "Box Temp" boxServicesTempSensorState excluded snmp-server filter "fan speed 1"...
View ArticleForum Post: RE: Dell-M8428-k chassis - failover between fabric switch port A1...
What method of redundancy are you using? What failover process are you performing? The M8428-K is installed in B1,B2,C1, and C2? What module is installed in fabrics A1 and A2?
View ArticleForum Post: RE: X1026 switch VLAN problem
By default all ports are untagged members of VLAN 1. Are the ports that cannot communicate being placed in a different VLAN? Can you provide some additional information on how the ports are configured?...
View Article