Forum Post: RE: IP ACL problems N-Series switch
What happens if you add the acl to a port?
View ArticleForum Post: Network simulator?
Does anyone know if there is an updated (or any) simulator for the F10 MXL, S, or N series switches? I see the FTOS 9.11 emulator for the S series but looks like it's lacking a few things and hasn't...
View ArticleForum Post: RE: N-Series switch log message CLI_WEB[UtilTask]:...
Hi, It looks like the idle timeout message for the management connection due to inactivity.
View ArticleForum Post: N2048 VPC/MLAG completely broken after upgrade to 6.3.3.10
I was getting a memory error every 30 seconds on this N2048 and I did some searching around and it said to try updating the firmware. I updated the firmware on one of the switches and rebooted it. It...
View ArticleForum Post: RE: N2048 VPC/MLAG completely broken after upgrade to 6.3.3.10
Hi, Can you upgrade the other switch to the same firmware?
View ArticleForum Post: RE: N2048 VPC/MLAG completely broken after upgrade to 6.3.3.10
Hi, The whole point in having VPC is so that one switch can go down and the network not collapse. I can't reboot the other switch until this one works properly. I rolled the firmware back and it works...
View ArticleForum Post: RE: N2048 VPC/MLAG completely broken after upgrade to 6.3.3.10
Sorry to reply to my own thread but you guys should definitely document that if you are using VPC there is no way of upgrading the switches one at a time.
View ArticleForum Post: Unable to share port between VLANs on old PowerConnect 2724
Greetings all, my company has an old PowerConnect 2724 switch and I'm passing the last month stuck in a odd situation: I want to create three VLANs for security purposes, with 1 specific port (of my...
View ArticleForum Post: RE: Endpoint ports: best practice
Every network is different and has different requirements. However, here are some basic tips that you could consider: 1. The use of spanning tree would be needed if there are multiple switches...
View ArticleForum Post: RE: Endpoint ports: best practice
On a related topic, I'm struggling to find a good explanation online of why enable portfast when STP could just be turned off per port. If you can help answer that, it would be appreciated. Regards
View ArticleForum Post: vlt peer routing and ip helper configuration
i m planning to migrate to dual configuration of S4048-ON with vlt per routing and i m wondering what is the best configuration for ip helper configuration
View ArticleForum Post: RE: IP ACL problems N-Series switch
It's not possible to assign the ACL to a port. It is a L3 instance with a lot of VLANs/subnet where I want to restrict the incoming and outgoing traffic to the specific VLAN/subnet. Beside that, I have...
View ArticleForum Post: RE: N-Series switch log message CLI_WEB[UtilTask]:...
I think also, but this is not the normal case. If so I would see this messages quit offen. In reality I saw this messages ( there were a lot of them) only two times on two different systems. It seems...
View ArticleForum Post: RE: N2000: Updating CPLD on stack members
It is not normal to only update the master unit, this could produce undesirable behavior and become a roadblock for future updates.
View ArticleForum Post: RIP version on S4048-ON version 9.10(0.1)
system. This command sets the RIP version for RIP traffic on the interfaces participating in RIP unless the interface was specifically configured for a specific RIP version.
View ArticleForum Post: RE: Spanning-tree problems on N2000 switch
The command to set the spanning tree priority is # spanning-tree priority. By default all of the switches are set to the same priority, which leaves root election to be determined by mac address....
View ArticleForum Post: RE: PowerConnect N3048P too many logging messages
You can change the logging level, but this would affect all messages that the switch records. It may be more productive to trace down the devices listed in the messages and try to resolve. Are ports 23...
View ArticleForum Post: RE: Powerconnect 3548 - New to managed switches
Something to keep in mind while working with the 3500 series switches, is that they are layer 2 switches. This means they will not be able to route between the VLANs, requiring that all VLANs be tagged...
View ArticleForum Post: RE: N3024 Switch Configuration
The N3024 will need to have all of the VLANs created on it, and an IP Address assigned to the VLAN. Then ensure that ip routing is enabled on the switch. Example: # interface VLAN 5 # ip address...
View ArticleForum Post: RE: Network simulator?
I am not aware of an emulator for the N-series switches. The MXL switches do not have a emulator iso, but the MXL also runs 9.11 and the commands should mostly be the same between the S and MXL. Is...
View Article
More Pages to Explore .....