Forum Post: switch config with tagged and untagged vlans
We have an N1548P switch which connects to a number of splicecom phones. Our PCs plug into the phones. Therefore the phones and PCs are sharing a switch port. Currently everything is in vlan 1. We'd...
View ArticleForum Post: RE: Check Temp for powerconnect 5324
I do not see any documentation that says that there is one.
View ArticleForum Post: RE: Check Temp for powerconnect 5324
If it has a temperature sensor in it, you may be able to find it running snmpget with the following oids: .1.3.6.1.4.1.89.53.15.1.9 .1.3.6.1.4.1.89.53.15.1.10 Hope this helps. -B
View ArticleForum Post: RE: switch config with tagged and untagged vlans
The voice vlan feature is probably what you need. It separates voice and data traffic. You use a general port to allow one VLAN to pass untagged traffic. Page 753...
View ArticleForum Post: RE: using vlan propagated by gvrp
This hadn't bothered me, because we migrated to Force 10 switches. But I need to use the old PowerConnect N4064 switches again, and this is still a problem. Please help.
View ArticleForum Post: Z9100-on remove one PEM don't have alarm
Hello, Why there is no alarm when I remove one of the PEM on Z9100-on? There is PEM removed log, and automatically cleared as below. TORSWA02(conf)#Sep 23 00:14:37: %STKUNIT1-M:CP %CHMGR-5-PEM_REMOVED:...
View ArticleForum Post: RE: Z9100-on remove one PEM don't have alarm
That is interesting, those alarms should persist as long as the module is not present. If you issue the command show alarms, does it still report the module being removed? what firmware is the unit on?...
View ArticleForum Post: RE: Z9100-on remove one PEM don't have alarm
-- Power Supplies -- Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------- 1 1 absent absent 0 1 2 up DC up 10464 TORSWA02# TORSWA02#...
View ArticleForum Post: RE: Z9100-on remove one PEM don't have alarm
-- Power Supplies -- Unit Bay Status Type FanStatus FanSpeed(rpm) --------------------------------------------------------------------------- 1 1 up DC up 10304 1 2 absent absent 0 TORSWA02#show alarms
View ArticleForum Post: RE: Z9100-on remove one PEM don't have alarm
The alarm should stay on, I am not sure why it is clearing. I don't see any commands that would affect this behavior. There is some newer firmware available. Would it be possible to schedule a time to...
View ArticleForum Post: Dell 55xx will not connect via SPF+ ports.
I am trying to connect a Dell 5524 with a Dell 5548 over a 350 foot fiber connection. I am using a pair Dell Networking, Transceiver, 10GbE SFP+ LRM Optic, 1310nm Wavelength, 220m reach on MMF - Kit's...
View ArticleForum Post: RE: Z9100-on remove one PEM don't have alarm
Hi, Do you have any suggested version? Thanks.
View ArticleForum Post: RE: Z9100-on remove one PEM don't have alarm
9.11.2.4 is the latest and suggested firmware. httpbit.ly/1WfO4Gs Keep us posted and let us know if this helps.
View ArticleForum Post: RE: Dell 55xx will not connect via SPF+ ports.
You can test the physical connection aspect of things by doing a loopback test. Plug both transceivers into the same switch and then connect the transceivers together with a short cable. They should...
View ArticleForum Post: RE: multiple shutdown / up message on 6 SW stack?
I have seen logs like this before, and sometimes it is hard to tell if it is the port flapping or spanning tree. The latest firmware addresses some scenarios, and would be worth scheduling to update....
View ArticleForum Post: Connecting two N3000 stacks via SFP+ ports
I have an N3000 stack and I am planning to connect it to another 2-stack of the same model. I want to connect using two fiber channels, so both SFP+ ports on the 2-stack will be taken up.
View ArticleForum Post: RE: N4032 configuration issues/doubts
I was able to: stop the looping and disabling of the port by matching the STP configuration with the main office; enable MLD, IGMP snooping and stack the switches using the QSPF+ modules. Now from...
View ArticleForum Post: RE: Connecting two N3000 stacks via SFP+ ports
You still want these two stacks to be separate? If that is the case, you will need to place the two interfaces into the same port channel. httpdell.to/2vaeqW8 Once the LAG is creating, then set it to...
View ArticleForum Post: add port to VLAN gets error wrong length
I have upgraded my Powerconnect 2848 to the latest firmware: 1.0.0.45 and since that I have the issue when I try to add a port to a VLAN I receive an error" null" with the description "wrong length".
View Article