Forum Post: What is the difference between the command "write" and "write...
What is the difference between the FTOS command "write" and "write memory" and "copy running config startup-config"?
View ArticleForum Post: RE: is my X1052P switch bricked?
************************************************** ***************** SYSTEM RESET ***************** ************************************************** Boot1 Checksum...
View ArticleForum Post: RE: Trying to SSH into a S60, but get error message: "no matching...
What SSH client are you using? Are there any updated versions of the software? Have you tried a different SSH client? I think you can get these messages if the SSH client is older. What firmware is the...
View ArticleForum Post: RE: is my X1052P switch bricked?
I suggest booting back to the other image and then flashing the new firmware again. Perhaps re-download the new firmware again.
View ArticleForum Post: RE: What is the difference between the command "write" and "write...
The write memory command saves the running-configuration which resides in the system RAM to the startup-configuration residing in the system NVRAM. Now, copy running config startup-config does the same...
View ArticleForum Post: RE: What is the difference between the command "write" and "write...
Both the "write memory" command and the "copy run start" command save the running-configuration to the file labeled startup-configuration. Each of these base commands (write and copy) also have other...
View ArticleForum Post: RE: What is the difference between the command "write" and "write...
Thanks Barrett for additional information!
View ArticleForum Post: RE: Dell F10 4810 logs=IP-4-ADDRMOVE...
hello I can have more detail i have the same problem and i have not conflict of address
View ArticleForum Post: RE: Dell F10 4810 logs=IP-4-ADDRMOVE...
he you have found the solution or explanation to your problem, I have the same problem thanks
View ArticleForum Post: RE: Small Router and Switch for VOIP QOS
Hi, Sorry for the late reply, thank you for the replies, i will read the documentation and get back to you if i need further information. Regards.
View ArticleForum Post: unrecognized command
The switch output is unrecognized command, when trying to set switchport mode to trunk - the exact same commands, as the switch enters, when applying it through the Web-UI. Example
View ArticleForum Post: RE: Failed to acquire an IP address on Vl1; DHCP Server did not...
I know, old thread but I just ran into this issue as well. Not so much an issue as it is an annoyance. Hopefully this helps someone along the way. The issue I ran into while running the # no ip address...
View ArticleForum Post: RE: unrecognized command
The X-series of switches is intended to be managed through the GUI. While it does have some functionality in the CLI, it is very limited and will not let you fully configure the switch from the CLI.
View ArticleForum Post: Interface status is up but protocol down on DELL s6010
i'm configuring a cluster to do pxe boot over dell s6010 switch. all the interfaces are showing up but protocol is down and machines are not able to reach management node. ports are assigned vlan 120...
View ArticleForum Post: 10GbE module for N3000 series switches tech details
Hello, wanted to buy 10GbE adaptor for my N3000 stack to connect them with another floor via Fibre Optics cable. On the Dell website I only found one module compatible with those switches 409-BBCZ.
View ArticleForum Post: RE: 10GbE module for N3000 series switches tech details
http://www.dell.com/learn/us/en/19/shared-content~data-sheets~en/documents~dell_optics_and_cables_connectivity_guide_march_2016.
View ArticleForum Post: RE: Interface status is up but protocol down on DELL s6010
Have you issued the command # no shut, on each of the interfaces? That should bring them up. httpdell.to/2i2lrTh
View ArticleForum Post: Check Temp for powerconnect 5324
Hello, How to I check the temp on a powerconnect 5324 through the Open Manager Switch Administrator? Thanks, Ramsey
View ArticleForum Post: RE: Check Temp for powerconnect 5324
I do not see a way to check the temperature. You may be able to create an alarm for it getting too hot. Page 191...
View ArticleForum Post: RE: Check Temp for powerconnect 5324
Does the 5324 powerconnect have a thermostat? I'm not finding any documentation noting that it does, nor do I see a way to set a temperature alarm with a web search.
View Article
