Forum Post: S4810T and iSCSI optimisation
Hello, I have a S4820T and want to activate iSCSI optimisation. I enabled iSCSI, and a "sh iscsi" gives the following: iSCSI is enabled iSCSI session monitoring is disabled iSCSI COS : dot1p is 4...
View ArticleForum Post: RE: PowerConnect 6248 - Uploaded firmware not visible in Active...
I am not sure why it is not listing the other image. From the CLI, what is listed when issuing the command # show version. perhaps there is a discrepancy between the GUI and CLI. If the image shows up...
View ArticleForum Post: RE: Cannot ping interfaces after configuring uplinks as trunks.
As new devices/links are made, it is normal for some topology changes to occur, and for ports to transition through the spanning tree states. This is just spanning tree ensuring that there are no loops...
View ArticleForum Post: RE: S4820T and 2 FN410T in FX2
That management interface config looks good to me. Have you tried connecting to the management interface with a client placed in the 192.168.152.0 subnet? Perhaps check the upstream switch arp table to...
View ArticleForum Post: RE: Cannot ping interfaces after configuring uplinks as trunks.
without that command #show spanning-tree shows the ports as forwarding even though I can't ping between the laptops. I'm guessing that this output refers to vlan 1 and the ports are in vlan 400...
View ArticleForum Post: RE: S4820T and 2 FN410T in FX2
Yes, this is the now running config. Before I had not a separated Subnet and no VLAN for the Management.And the IP-Route was missing. That's why the traffic had 2 ways.
View ArticleForum Post: No PowerConnect 6248 Topology with SolarWinds
I'm using SolarWinds NPM to monitor my host of switches, including several PC 6248s. I'm trying to get the topology working, but I'm not getting anything from most of these switches. I have them all on...
View ArticleForum Post: RE: PowerConnect 1052P lost POE capability
It is just this one giving you the problems? Any messages recorded in the switch logs? You could try to update the firmware on the switch, see if it helps out at all. http://dell.to/2tPgCT7
View ArticleForum Post: RE: S4810T and iSCSI optimisation
It appears that the CAM table allocates to 0, and without any CAM space allocated the monitoring feature is not enabled. You will need to modify the CAM table to include space for the session monitor....
View ArticleForum Post: RE: Cannot ping interfaces after configuring uplinks as trunks.
Thanks for the update, glad to hear you found the solution. Cheers!
View ArticleForum Post: RE: S4810T and iSCSI optimisation
Ah, thanks. I'll Change this with the next downtime.A reboot is required as far as I understand this.
View ArticleForum Post: RE: No PowerConnect 6248 Topology with SolarWinds
Thanks for the reply. I have that image installed already, so I have the MIBs , but can't find how to install them onto the switch. Can you link me to any instructions for that?
View ArticleForum Post: Flood of %iSCSI-5-ISCSI_OPT_NEW_TCP_CONNECTION errors
%STKUNIT0-M:CP %iSCSI-5-ISCSI_OPT_NEW_TCP_CONNECTION: New iSCSI TCP Connection is discovered: source ip-address : xxxx source port: 55717 destination ip-address: xxxxx destination port: 3260 Anyone...
View ArticleForum Post: Switch configuration For IP Survailance system
we are using Dell N Series Switches For Edge Swicthes(N3024P) and Dell N series For Core (N3024F) For IP surveillance system Project the question is there any Special Configs on Edge and Core N...
View ArticleForum Post: RE: No PowerConnect 6248 Topology with SolarWinds
LLDP allows network devices to advertise and expose their physical descriptions. This description including physical topology is stored in MIB and presented to SNMP.
View ArticleForum Post: RE: how to configure default gateway on out-of-band mgmt 7000 series
Yes , you need to only put in the interface Out-of-band tje command IP ADDRESS IP MASK DEFAULT-GATEWAY for example, put the command IP ADDRESS 192.168.0.x 255.255.255.0 192.168.0.x
View ArticleForum Post: RE: PowerConnect 6248 - Uploaded firmware not visible in Active...
Hi Daniel, Here Some My Documentations. Hope this will help you drive.google.comview Thanks AT
View ArticleForum Post: RE: No PowerConnect 6248 Topology with SolarWinds
MIB updates is included when the firmware update is applied. Just make sure that the MIBs were part of the firmware package. You might consider contacting SolarWinds to about including these MIBs into...
View ArticleForum Post: RE: Switch configuration For IP Survailance system
The setup for video can be very similar to the concept for voice. Isolate the traffic to a dedicated VLAN, use QoS to assign incoming video traffic a higher priority, check topology to ensure there is...
View ArticleForum Post: RE: No PowerConnect 6248 Topology with SolarWinds
The MIBs are uploaded along with the .stk file that I upload to the switch for the firmware update?
View Article