Forum Post: RE: VLAN Setup / Dell PowerConnect 2816 and 2824
Thanks for the update, glad to hear it helped.
View ArticleForum Post: RE: How to save configuration files from Switch to tftp Server
Someone from the SpiceWorks community just posted up this PowerShell script that may be useful. httpbit.ly/2qsFa1u
View ArticleForum Post: RE: howto save Running Config File from CLI ?
I know this is an older thread, but wanted to come back with some updated information for anyone searching. Here is a KB article with some information on backing up configurations on the PowerConnect,...
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
Just bumping in case anyone has any suggestions on how to get the ports in to an port channel -- thanks
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
What mode is the switch in? You may need to change to PMUX mode. # stack-unit unit iom-mode programmable-mux Once that is done you should have some further commands available. Page 145:...
View ArticleForum Post: RE: VLAN validation on PowerEdge M I/O Aggregator switch
Testing conectivity across different VLANs is not usually done by pinging from the switch, as this ping is done from the management IP address and cannot be channeled through specific VLANs.
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
Looking at going in the PMUX mode, it sounds like you have to reboot to change the mode. Is there any other impact (i.e. would any of the existing VLT config be lost)?
View ArticleForum Post: RE: VLAN validation on PowerEdge M I/O Aggregator switch
Got your point thank you for your help.
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
Sorry, I did not catch that, so this switch is setup as a VLT peer with another switch? In that case you will need to leave it in vlt mode. I will keep doing some research.
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
Thanks -- to confirm it is in VLT mode with another aggregator in the same chassis. All the other ports going to the servers are in port channels which are working without issue. Just the first port...
View ArticleForum Post: RE: Powerconnect 3524P serial port disabled?
I checked the serial cable we had and confirmed it was DB9. According to the linked article, I am using the correct pinout for the switch I have. I have tried every baud rate possible and have had no...
View ArticleForum Post: RE: Powerconnect 3524P serial port disabled?
I cannot think of anything else. If it was just one switch, I would think that the port would be faulty. With a large number, there has to be something else going on. I found another diagram of the...
View ArticleForum Post: Very Old 6248s with NO enable command
So I have inherited these Poweconnect 6248s and they have the original firmware 2.0.0.12, when I log in with the admin password, there is no enable command. all I have are a few show commands, has...
View ArticleForum Post: RE: Very Old 6248s with NO enable command
Hi, Will it let you show the running config? Can you get into the Web GUI? Are you able to flash to newer firmware from the boot menu?
View ArticleForum Post: RE: Very Old 6248s with NO enable command
Negative to all three questions, I am trying to get into the webGUI with the same username and password I used to Console in, But it keeps telling me it is "invalid. I have never seen this before, The...
View ArticleForum Post: RE: DHCP Relays Dell S3100 Series Switch Issues
I was able to add it to the vlan interface without issues. I think I mis-read something in the set up guide. thanks for the reply!
View ArticleForum Post: RE: Very Old 6248s with NO enable command
Will it let you into the boot menu to clear everything?
View ArticleForum Post: SFP Interface model FTLF1318P3BTL
Hi. I have some SFPs interface model FTLF1318P3BTL, but with differences in a code. Some of them have 15-37, others 15-38, others 15-36. When I connect different codes, the SFPs don´t get connected....
View ArticleForum Post: RE: IGMP snooping multicast issue DELL 4032f MLAG connection to...
Unfortunately, you probably wont be able to get multicast to work with this MLAG setup. If we look at the features synchronized between MLAG peers, IGMP snooping is not one of them. Page 1023:...
View ArticleForum Post: RE: SFP Interface model FTLF1318P3BTL
Those codes should be the date codes. The first number being the year and the second number being the week in the year. So all three you listed would have been made in September of 2015.
View Article
More Pages to Explore .....