Forum Post: RE: PowerConnect 3448P PoE Mode A or Mode B
Thanks for getting back to me. I updated the firmware several months ago. I am running the latest version. The Cloud Key is Mode B only. So, it will only work if the PowerConnect is Mode B as well.
View ArticleForum Post: RE: PowerConnect 3448P PoE Mode A or Mode B
I have not been able to find any documentation with that information.
View ArticleForum Post: Mounting options for a Z9000?
I can't find any rail kit DP/N for the Z9000, what are my options for mounting this 2U switch?
View ArticleForum Post: RE: Mounting options for a Z9000?
From the install guide it used rack ears and not a rail kit. Page 18...
View ArticleForum Post: RE: Mounting options for a Z9000?
N243X won't work, already tried it. It has several screw holes along the side for mounting, see picture:
View ArticleForum Post: How to create new port channel on auto-lag enabled switch when...
I am totally new to dell switches (cisco background) and have been asked to create a port channel split over a pair of existing dell aggregator enclosure switches. All the other ports which are...
View ArticleForum Post: RE: Multiple Vlan Trunking between Cisco and Dell switch
Thanks for your reply. To config trunk mode as "general" did not make difference. I configed both Cisco and Dell to run MSTP as suggested by Dell docu, and also upgraded Dell7048P to the latest code...
View ArticleForum Post: RE: Multiple Vlan Trunking between Cisco and Dell switch
Hello, looks like switches can't exchange special VLAN 1 information, on the Cisco side you shouldn't add vlan 1 into allowed vlan list, since this vlan default native and should be untagged. Also I...
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
I believe you should apply your vlans on the configured port-channel and you can try to enter no auto-lag enable on the port level as well. Can check this clearly since I don't have aggregators at this...
View ArticleForum Post: resetting a serial port password
Got an N3024 off the shelf and it has a username password set on serial port. what are the options to reset this so I can get into it? Any suggestions welcome. B
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
Thanks - unfortunately the switch does not take the command to default the interface config back. (the only option off default is default vlan: agg1(conf)#default ? vlan-id Set default VLAN Id I tried...
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
Also you should add interface to port-channel first, than it should allow you to add port-channel configs. What switch says, when you trying to add those commands? int te0/1 port-channel-protocol LACP...
View ArticleForum Post: RE: How to create new port channel on auto-lag enabled switch...
Thanks -unfortunately per below output I tried removing the vlans and the auto-lag but it doesnt give me any the option to issue the port channel cmd (I''ve listed the ones available under the...
View ArticleForum Post: PowerConnect 6224 connector to RPS-600
This is probably the dumbest question I ever asked: I sent a technician to install on our PowerConnect 6224 a recently purchased RPS-600. The technician calls me back and tells me that the connector...
View ArticleForum Post: Dell Enterprise Hardware & Software Updates, May 1-5
PowerEdge T30 TPM 1.2 Firmware Update Utility (64-bit), Nuvoton TPM, 5.81.2.
View ArticleForum Post: This Week's 5-Star Enterprise Support Articles
PowerEdge Servers - What are the different RAID levels and their specifications?
View ArticleForum Post: DHCP Relays Dell S3100 Series Switch Issues
I have a Cisco core, I am integrating Dell into my network because I have heard great things. I need to set up DHCP Relays on my vlans (coming from a cisco background) and found that it has to be...
View ArticleForum Post: RE: DHCP Relays Dell S3100 Series Switch Issues
An interface needs to have an IP address to be considered layer 3. I would think that you could apply an IP address to a vlan and enable ip helper on that VLAN interface. Have you tried that? Page 246...
View ArticleForum Post: VLAN validation on PowerEdge M I/O Aggregator switch
I am trying to validate VLAN which are coming from upstream Nexus 5K switch, when i check the "poweredge-m-io-aggregator_Administrator Guide7_en-us" PDF we have ping command with below options, non of...
View ArticleForum Post: RE: VLAN Setup / Dell PowerConnect 2816 and 2824
Just a quick follow-up -- after making the changes to specific switch port CoS as needed, the sound quality of VOIP calls is much better. Thank you!
View Article