Forum Post: RE: Frameproblem
Here are the commands to increase MTU on each switch. N1524 = # system jumbo mtu {frame size} Page 429: httpdell.to/1SVu3Bp 5424 = # port jumbo-frame Page 159: httpdell.to/2jqfv2k
View ArticleForum Post: RE: How to convert Hundred Gig port on DellZ9100-ON switch to...
While this KB article is not specific to the Z9100, I believe the info is still pertinent. httpdell.to/2iXlOLC It indicates that you may need to add the interface to the quad capable profile list. Here...
View ArticleForum Post: RE: Port security 6248
When port security is enabled on an interface, all dynamic entries learned up to that point are flushed. So the interface should be starting at 0. It sounds like this flushing of entries is not...
View ArticleForum Post: RE: MLAG + VTLi + STP No traffic
Hello Daniel! Thank you for answer, I also double check the configs reset switches and config everthing again with no luck. Today with no changes made on weekend is working now, vlans 1716 and 1717...
View ArticleForum Post: RE: Resetting a Powerconnect 5424 to factory defaults without the...
Much appreciated for the info, I am not sure how to verify the right pinout? The cable has no marks or numbers it is a standard DB9 male to usb. does that tell you anything? I have tried putty, hyper...
View ArticleForum Post: RE: Resetting a Powerconnect 5424 to factory defaults without the...
With 3rd party cables it can be hard to know the exact pinout. My guess would be that the cable is not compatible. Building a cable, sourcing a cable with known pinout, or finding the original cable...
View ArticleForum Post: RE: MLAG + VTLi + STP No traffic
Hello! After doing some test, Finally I get working the VPC part. Just change STP mode to rapid-pvstp and now everything works great! Now I will focus on integrate VLT. Thank you!
View ArticleForum Post: RE: Resetting a Powerconnect 5424 to factory defaults without the...
Daniel I found this cable on Amazon from StarTech is is a Null modem cable DB9 Female to USB Pin Out noted is 1 DCD 2 Txd 3 RxD 4 DTR 5 GND 6 DSR 7 RTS 8 CTS 9 RI do you think this will work?
View ArticleForum Post: RE: Resetting a Powerconnect 5424 to factory defaults without the...
Never mind answers my own question NO it will not :)
View ArticleForum Post: RE: Resetting a Powerconnect 5424 to factory defaults without the...
Question if I only change the TxD, RxD, RTS, and CTS to the correct pins will I be ok does the DCD, DTR, DSR, RI matter if they are hooked up? the pin out to mention as noting on those pins. Pin Out...
View ArticleForum Post: What am i am missing with rip
How can I disable on the new firmware on the n3024? I have it disabled, but it still shows rip router in show run. I am setting up of now. The GUI and command line show it disabled.
View ArticleForum Post: RE: MLAG + VTLi + STP No traffic
Thanks for the update. Glad to hear thing are working now. Cheers
View ArticleForum Post: RE: Resetting a Powerconnect 5424 to factory defaults without the...
DCD, DTR, DSR, RI are not used for the console connection on these switches. You are fine with leaving these pins as is.
View ArticleForum Post: RE: What am i am missing with rip
Hi, As long as it is not configured it won’t do anything. So if it shows disabled that is enough.
View ArticleForum Post: RE: How to convert Hundred Gig port on DellZ9100-ON switch to...
I don't see "quad-capable-profile" command in our switch. Error while trying to run "stack-unit 1 quad-capable-profile 29" Dell_Z9100_S6(conf)#stack-unit 1 quad-capable-profile 29 ^ % Error: Invalid...
View ArticleForum Post: RE: What am i am missing with rip
ok, that is crazy to me but ok that works then, yeah it shows disabled both in GUI and terminal. just to make sure, console(config-router)#no enable console(config-router)# That is the right way in...
View ArticleForum Post: RE: How to convert Hundred Gig port on DellZ9100-ON switch to...
I apologize that the command was not an option. Lets check the interface to see if it has any configuration already on it. We can use the following command to see which interfaces do not have the...
View ArticleForum Post: RE: Port security 6248
Age Time (seconds)............................. 1200 Response Time (seconds)........................ 1 Retries........................................ 4 Cache Size........................................
View ArticleForum Post: Reset Password on DELL Switch N3024
Hi All, Actually I forget the username/password on my DELL N3024 Switch. How to reset the username/password but still have the switch configuration? Please kindly need your help.
View Article
