Forum Post: RE: Storsimple dell n3024
I am not sure what else we can check on this one. Are we sure the controller being connected to is the active controller on the StorSimple 8100?
View ArticleForum Post: RE: m6220/m1000E: How to create sub-net for each blade?
Can you give us some more information about your topology/setp? What does the M6220 connect to? What device is 10.10.10.1? Where does 10.10.10.1 reside on the network? These IP addresses are being...
View ArticleForum Post: RE: Advice on how to Create Redundant Switch Configuration
Stacking is probably going to be your best option. httpdell.to/2dZ1Qif MLAG provides redundancy, but it does not support single homed devices. httpdell.to/2eNH5sh
View ArticleForum Post: RE: Overlapped VLANs
Thank you DELL-DANIEL for pointing the direction. It seems a very long road to go. I'll try anyway. Thanks again.
View ArticleForum Post: RE: What needs more bandwidth, The MLAG connections of the switch...
I'm trying to understand mlag use cases in storage network (iscsi/vsan) and active/passive NIC teaming for servers either windows 2012 (native teaming) or vmware (vswitch teaming).
View ArticleForum Post: RE: Storsimple dell n3024
Yes. I don't know if this does help but here is the configuration of the port on the storsimple Name DisplayName DisplayValue DATA2 Flow Control Rx & Tx Enabled DATA2 Header Data Split Disabled...
View ArticleForum Post: PowerConnect 6224 increased latency and dropping packets since IP...
I have a 6224 which until recently was running quite nicely without an IP, or http access, but I don't know what configurations may have been made via console since it came out of the box.
View ArticleForum Post: Unencrypted Telnet Server
vulnerable found on my Dellnetwork administrators IO module R1-2210 "Unencrypted Telnet Server" what is the best practice to disable telnet server. TIA.
View ArticleForum Post: duplicate multicast packet
Hi I have installed new blade server with EXSI-OP on our Dell power edge 1000 chassis,in th company. the xvm that i created on the blade server gained duplicate multicast packet. unicast works fine....
View ArticleForum Post: RE: Storsimple dell n3024
It is hard to tell from that output, but is the controller sending VLAN tagged packets?
View ArticleForum Post: RE: Storsimple dell n3024
Not sure, but is there anyway to check on the dell side?
View ArticleForum Post: RE: What needs more bandwidth, The MLAG connections of the switch...
With the N-series and MLAG, the peer link is only going to carry vlan/network traffic when a link is down on one of the peers. Where as with VLT, the vlan/network traffic can always traverse this...
View ArticleForum Post: RE: PowerConnect 6224 increased latency and dropping packets...
While 3.3.3.3 is newer than what was on the switch, that version is over 4 years out of date. When updating firmware, I suggest checking out the latest version. http://dell.to/2b45NRO Is this issue...
View ArticleForum Post: RE: Storsimple dell n3024
Even if it was tagged, I would think the interface would still show a counter for packets received, and it is not. The switch itself is operational, we know the hardware and config work fine with other...
View ArticleForum Post: RE: Storsimple dell n3024
Ok, it not tagged seeing as we only have vlan1 on that switch, I did contact Storsimple support, and did troubleshoot on that end and it only show the connection as disabled
View ArticleForum Post: RE: Unencrypted Telnet Server
The command to disable the telnet server is: # no ip telnet server Page 255: httpdell.to/2eFPXko
View ArticleForum Post: RE: PowerConnect 6224 increased latency and dropping packets...
Thanks for the reply. I'd like to get the firmware up to the August 2016 release, but the stack is our main production switch and upgrading it risks knocking out the whole business. It will get done,...
View ArticleForum Post: RE: duplicate multicast packet
Do you have multiple multicast sources? Or are you seeing duplicate packets from the same source?
View ArticleForum Post: RE: PowerConnect 6224 increased latency and dropping packets...
Thanks for the update. Those numbers look good. If the issue comes back, let us know if these numbers change while the issue is occurring.
View ArticleForum Post: Dell 4064F and Copper SFP (100BASE-T) - Link Status no detected
Type.............................. SFP Media............................. 1000BASE-T Serial Number..................... MTCGETC024483 Dell Qualified.................... Yes Data...
View Article