Forum Post: RE: N3048 or S3148
I don't have a compatibility list, but if that transceiver worked in the 6200 series, it will work in the N3000 and S3100.
View ArticleForum Post: RE: SNMP OID CPU, InBroadcastPacket for Powerconnect 5324, 6248
Hi Daniel, I will try the way that you recommended and reply soon. Thanks for your support!
View ArticleForum Post: Powerconnect 6224 stacking over XFP
Just curious about something I've been trying to find a hard yes/no answer on but haven't had any luck. Long story short, I am looking at picking up a pair of 6224 switches and would want to set them...
View ArticleForum Post: RE: Powerconnect 6224 stacking over XFP
Only CX4 modules may be used for stacking on the PowerConnect 62xx. You can find more information on all of the supported modules for the 62xx under "N-Series Campus Switches" at the following link....
View ArticleForum Post: RE: Powerconnect 6224 stacking over XFP
Figured as much, but worth a shot to ask. Was hoping it would be possible, but I can deal with the two as linked and unstacked. Thanks
View ArticleForum Post: Dell Enterprise Hardware & Software Updates, October 3-7
PERC H730/H730P/H830 Mini/Adapter/FD33xS/FD33xD controller firmware 25.4.1.
View ArticleForum Post: RE: Dell S6000 unsupported module type
Hi, Is it always module 2? It could be an issue with that power supply slot. If you reseat that power supply with the switch on does it change status?
View ArticleForum Post: RE: how to set jumbo frame on some specific interface
We have problems with our equalogic and the guys on the support insist that we switch to jumbo frame.
View ArticleForum Post: pxe and lag on N3048 and 7048
Hi I would like to connect a switch to a stack of switch for redundacy but i need to install it frequently with pxe. what is the best option? can i use lacp or should i stay with stalic lag?
View ArticleForum Post: ACL configuration on an N3048p
Basically we have 5 VLAN's and we need to segregate a few of them out and i am having some issues with this. I have tried a load of different settings but cant seem to get anything to work. So my VLANs...
View ArticleForum Post: RE: pxe and lag on N3048 and 7048
I have a tendency to use LACP when available, but really you shouldn't have any issues as long as the same mode is used on both ends of the connection.
View ArticleForum Post: RE: ACL configuration on an N3048p
I suggest starting small and slowly building on the ACL, testing along the way. Using the scenario you outlined, you could perhaps start with one client in a VLAN and deny it access to the subnet of...
View ArticleForum Post: RE: ACL configuration on an N3048p
Here is a whitepaper on Private VLANs for the N-Series that I think will also be helpful. httpen.community.dell.com/techcenter/extras/m/white_papers/20438600 -B
View ArticleForum Post: RE: Dell S6000 unsupported module type
boot device : flash file : systema (Dell Networking OS system://A Partition) WARNING: skipping large memory map entry: 0x100000000/0x140000000/0x1 Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001,...
View ArticleForum Post: RE: Dell S6000 unsupported module type
Are the power supplies AC or DC? Are you able to update the software from 9.7 to 9.10?
View ArticleForum Post: RE: Dell S6000 unsupported module type
The power supplies are AC, and I am not able to update to 9.10, you think it might be a software issue?
View ArticleForum Post: RE: Dell S6000 unsupported module type
Yes, since it works otherwise, if was actually both power supplies not working it wouldn’t boot up.
View ArticleForum Post: RE: Recommended Dell SFP & SFP+ transcievers for M8024-K
Here are the part numbers I have listed. The SFP transceivers are only supported in the fixed ports, and will not work in the FlexIO module. 10GbE SFP+ SR = RK0CX SFP-1G-SX = 63GGJ SFP-1G-LX = VYW04...
View ArticleForum Post: RE: pxe and lag on N3048 and 7048
my problem is the support of pxe. As far as i can see there no support for a lacap fallback mode when using pxe in dell switches.
View ArticleForum Post: RE: pxe and lag on N3048 and 7048
Your observations are correct, the switch does not offer a fallback mode feature for LACP.
View Article