Forum Post: RE: Powerconnect 6248P quit forwarding traffic - MAC Pause Frames
Hi, There is not anything specifically for blocking MAC pause frames. You could try enabling flowcontrol on the ports. Page 292
View ArticleForum Post: RE: PC 2848: Will it work with a GLC-FE-100LX?
Hi, It is not validated, however it is possible that it may work as we have 1000LX transceivers.
View ArticleForum Post: RE: N3024 - finder is slow with 10Gbe
Hi, The switch is brand new, i'm not sure where i can find the firmware version? i use the 6,2,7,2 administrator preferences and interfaces advanced firmware is V1.08 I finally manage to avoid my issue...
View ArticleForum Post: RE: M8024-K port-channel to two Nexus 3000's - loop detected
Where is the loop being detected? between the Cisco and the PowerConnect? Do you have a brief topology diagram you can share with us? Perhaps post up the configs? We can help look things over.
View ArticleForum Post: RE: N4032 two switch vrrp
In most deployments I have seen, the switches performing VRRP are not typically utilized as distribution/access switches on top of being core switches. I would think that you could get this setup to...
View ArticleForum Post: RE: Dell PowerConnect 2848 uplink and management
Unfortunately I do not have a topology of our network. But basically: Port 1 to 43 are being used for customers, VLAN1021, all ports untagged on the switch. Port 44 is the uplink from our core core...
View ArticleForum Post: RE: N4032 two switch vrrp
The purpose of this setup with two firewalls and two switches are for the redundancy. the left side devices such as sw1 and fw1 will be forwarding the traffic in normal operation. and when any devices...
View ArticleForum Post: RE: Powerconnect 6248P quit forwarding traffic - MAC Pause Frames
Thanks for the reply. It got me looking more at flow control and what I have gathered is that if flow control would have been disabled on our LAN switches we would not have had the outage as the...
View ArticleForum Post: RE: N4032 two switch vrrp
Correct, SW1 will need to have tracked interfaces for the FW1 connection. This will ensure that once SW1 no longer has a path out FW1, it will adjust it's VRRP priority. Then SW1 will become VRRP...
View ArticleForum Post: RE: 62xx - is routing between Vlans with interfaces in "Access...
to route between VLANs an IP address needs to be assigned to the VLAN, and ip routing needs to be enabled on the switch. If the VLAN does not have an IP address, it will not be able to be routed. The...
View ArticleForum Post: This Week's 5-Star Enterprise Support Articles
Here are this week's top-rated support articles based on accuracy, usefulness, & ease of understanding: Configure iDRAC and systems management options on PowerEdge servers Understanding HDD types,...
View ArticleForum Post: RE: N4032 two switch vrrp
Thanks Daniel, we will do the migration on this coming Saturday morning. will keep you posted and post here if there is some more doubt before the migration. Thanks again.
View ArticleForum Post: RE: N3024 - finder is slow with 10Gbe
If you do a show run it should be at the top of the output.
View ArticleForum Post: RE: spanning-tree portfast or switchport mode general
I need a little help here. I'm trying to put the video on it's own Vlan I first started off with VLAN 121 address 172.16.121.1/24. On the core I was able to get out to the IE. I went to the IDFC and...
View ArticleForum Post: RE: 62xx - is routing between Vlans with interfaces in "Access...
Daniel, please forget about my first original question - I've gone dumb - nodes needs to know about routing paths which completely hmm. but that "trunk" mode seems bizarre. Port channel 22 connects...
View ArticleForum Post: RE: N3024 - finder is slow with 10Gbe
Thanks for the info, so the firmware is 6.2.7.2.
View ArticleForum Post: How to enable Iscsı Ports Dell X1026 Switch
Hi there, I got Dell X1026 Iscsı Switch and I couldn't provide connection between Switch and MD Controller's mgmt port. However when ı try to wire up between switch and server ethernet port for...
View ArticleForum Post: RE: spanning-tree portfast or switchport mode general
Is port channel 9 a trunk carrying multiple vlans or just one? If it works when vlan 41 is on there and vlan 41 looks to be on all the switches it doesn't have to route through other vlans.
View ArticleForum Post: RE: 62xx - is routing between Vlans with interfaces in "Access...
If it is working while in Access mode, but not Trunk mode, it makes me think that there is perhaps a misconfiguration between the connecting switches. Is x.x.x.100 also configured to be Trunk mode? Can...
View ArticleForum Post: RE: spanning-tree portfast or switchport mode general
Channel Ports Hash Algorithm Type ------- ----------------------------- ------------------- ch9 Active: 1/g47, 2/g7, 2/g8, 6 2/g17, 3/g47, 4/g47, 5/g1, 2/g3 41 BCVOIP 2/g11 Static Required...
View Article