Forum Post: N3000 - Vlan Interface - NO description option available
Folks, Can you please advise if this is by design or if this in an 'unintended feature'? I am in the process of migrating a config from a cisco switch and not having the ability to label the various...
View ArticleForum Post: Power Connect 2724 Loud Fan
Hello, The fan in our Power Connect 2724 has become very loud. Is there anything we can do to remedy this? We're concerned with it overheating. Please advise. Thank you, Sharon
View ArticleForum Post: RE: Power Connect 2724 Loud Fan
Is the fan just audibly loud and hard to work around? If so, there are several 3rd party vendors and videos that show how to replace the fan. If the fan is physically going out and has stopped working,...
View ArticleForum Post: RE: N3000 - Vlan Interface - NO description option available
Try this command out, see if it works for you. console(config)#vlan 2 console(config-vlan2)#name "Management VLAN" Page 809 of the cli guide. httpdell.to/1SVu3Bp Hope this helps.
View ArticleForum Post: RE: N3000 - Vlan Interface - NO description option available
What I am actually looking for is the description feature for the SVI itself as opposed to the actual vlan name. The logic being that as with cisco the VLAN NAME value has a shorter character limit...
View ArticleForum Post: RE: N3000 - Vlan Interface - NO description option available
I don't see a command on this switch that would change that value. What command would you use on a Cisco switch?
View ArticleForum Post: RE: Dell force10 MXL cannot access Web GUI
I am looking for the updates for the Dell Force10 MXL Switch. Can you please let me know where they can be found. Thank You.
View ArticleForum Post: RE: Force10 MXL 10/40gb Firmware Update
Did you ever find a location where the firmware updates can be gotten from? I am in the same situation.
View ArticleForum Post: RE: Dell force10 MXL cannot access Web GUI
To receive updated firmware for your Force10 switch, you will need to have an active subscription. Then login to the Force 10 portal site and the downloads will be available. http://bit.ly/1LYW4VW
View ArticleForum Post: RE: Set up Voice/Data VLANs on ports, Voip works but Data doesn't
- Is there a core switch on the network that has IP addresses assigned to each one of the VLANs? If so what port does the N2048P use to connect to the core switch. - Where does the DHCP server reside...
View ArticleForum Post: RE: Power Connect 2724 Loud Fan
My apologies, the fan LED is only on the 2748. I would double check and make sure there is nothing impeding air intake. The fans are designed for use in a server room where acoustics are of low concern.
View ArticleForum Post: RE: 62xx - routing or vlan config error ?
Other hosts on Vlan3 do not stop being accessible when a(any) port in Vlan3 has a connection, which is what happens to hostXX, but those hosts/nodes do NOT use 10.5.6.1 has the default gateway. Even...
View ArticleForum Post: RE: 62xx - routing or vlan config error ?
on hostXX I deleted this routing: 0.0.0.0 10.5.6.1 0.0.0.0 UG 100 0 0 p3p1 # and 10.5.6.1 is switch's vlan5 it's vlan4 naturally, typo.
View ArticleForum Post: conditions for Vlan IP to be up? PC 64xx
when does an IP of a Vlan go & stay UP? How does a switch decide when to take and keep it down? regards
View ArticleForum Post: RE: DELL N1524 and OME
Have you had a look at the logs on the switch? From the CLI of the switch run the command # show logging. That will give you a detailed list of messages.
View ArticleForum Post: RE: Dell PC5548 problem with connection to Gallagher 6000 Control...
Have you thought about setting up a port mirroring session on port 45? You could grab two packet captures. One without the Cisco switch, and one with the Cisco switch. Then compare the two with each...
View ArticleForum Post: Stuck at pinging out of vlan on S3048
Hi. trying to get started on setting up a new network with a S3048 as the core switch. As a starter i've created a vlan - id 100. This has been assigned to port ge 1/1. Connected to this port i have...
View ArticleForum Post: N1548p Reformat file system ?
Hi, Yesterday my N1458p only shows the boot menu and can't load the image, should I try reformat and restore file system option ? Any recovery guide you recommend ? Best Regards.
View ArticleForum Post: How to enable Internet access for VLAN's.
!System Description "PowerConnect 6248P, 3.3.3.3, VxWorks 6.5" !System Software Version 3.3.3.3 !Cut-through mode is configured as disabled !
View Article