Forum Post: RE: Will NetApp Storage is compatible with Dell Force10 S60
Right, it should work.
View ArticleForum Post: RE: N4032 configuration issues/doubts
I was able to apply the VLANs configuration to the ports on the second switch and now I can see it when I do show run, show vlan, show interfaces status, etc.
View ArticleForum Post: RE: N4032 configuration issues/doubts
Yes, it does. But somehow stopped recognizing the user and password credentials no matter how many users or times I change the password. Is there a cache that needs to be clear to apply the new login...
View ArticleForum Post: Replace failed M8024, not stacked, Module B1
I need to replace Mod B1 10GbW XAUI. Device becomes primary when plugged into chassis, bad. Remote location and I have access to CMC. Looking for steps to replace, put IP on it, restore backed up...
View ArticleForum Post: RE: N4032 configuration issues/doubts
You shouldn't need to, have you tried rebooting the switch?
View ArticleForum Post: RE: Replace failed M8024, not stacked, Module B1
You can use the copy command to copy the current config to a tftp server, then use the copy command to copy the config from the tftp server to the new switch. Here is a KB article with some directions...
View ArticleForum Post: Reset SNMP port status
We have a dell 6224 switch which is being monitored using SNMP. One of the servers connected to that switch was turned off as we don't need it anymore. Now the switch SNMP engine says the status of the...
View ArticleForum Post: RE: Will NetApp Storage is compatible with Dell Force10 S60
Our Storage Interoperability group has never performed any validation on this combination. Our validation efforts concentrate on DELLEMC storage with the various switches.
View ArticleForum Post: RE: Need help to control broadcast
We can share our screen remotely for you if you can help we have large local area where we have almost 20 switches of cisco if you can configure only one and let us know we will use the powerconnect only.
View ArticleForum Post: DHCP snooping between multiple switches and how to make exceptions
The issue that I am experiencing is that DHCP requests can't be delivered from DHCP server on sw1 to DHCP client server on sw2 when DHCP snooping is enabled. Client servers on the same switch as DHCP...
View ArticleForum Post: RE: Reset SNMP port status
Typically port status is not polled, but rather gained from a trap. It could be the SNMP tool you are using may be holding onto the last trap information received. The 2 is probably a "port down" status.
View ArticleForum Post: RE: Need help to control broadcast
When storm control is enabled on interface 1, and the broadcast packet threshold is exceeded, all communication across all devices on the switch is interrupted? no device is able to communicate with...
View ArticleForum Post: RE: Need help to control broadcast
Here is the link for the latest firmware: httpdell.to/2fxmU3J If the switch is not up to date, it may be worth it to update and test to see if the firmware will help at all with this behavior. Here is...
View ArticleForum Post: RE: Reset SNMP port status
The information is polled with LogicMonitor and it's polling lots of info on each port (about 20 metrics per port and status is only one of them). Acknowledging the alert on the LogicMonitor side will...
View ArticleForum Post: RE: Reset SNMP port status
What do other ports show as their status? Is the (off) server cable still plugged in, or is that switch port now empty (nothing plugged in)? All SNMP is doing is reporting what is in the MIB, I doubt...
View ArticleForum Post: RE: DHCP snooping between multiple switches and how to make...
Just to clarify, if you disable snooping on one of the switches, everything works fine? Can you just leave snooping disabled on the one switch? Or does this introduce a different issue?
View ArticleForum Post: RE: Powerconnect 5324 after upgrade firmware still show 2006...
When I try to update firmware success show no erore .but when try to update show faild I'll select image 1 and 2 both show erore on boot update.
View ArticleForum Post: RE: Reset SNMP port status
The cable is still connected to the switch as the old device was not physically removed yet. on the web ui the port looks just like any other disconnected port. The strange thing is that I tried...
View Article