Forum Post: RE: Force10 s4810-ON FTOS firmware
Does the model show up in the list of your devices? Sometimes it just needs to be added to your account.
View ArticleForum Post: RE: N Series Switch Mac-Address Port-Security
Since you are already entering every MAC address, you might want to consider using a MAC based ACL. This ACL could be configured to allow a list of MAC addresses, then deny everything else, and can be...
View ArticleForum Post: RE: Force10 s4810-ON FTOS firmware
S4810-ON not support install DELL FTOS. it only support 3rd OS.
View ArticleForum Post: RE: both Core Switches are Master for vlan 10 on N3024F core...
problem solved with changing the spanning tree protocol from RSTP to PVST, with RSTP the uplinks to the core switch were blocked by RSTP which makes the VRRP not working properly and stay in master...
View ArticleForum Post: RE: PowerConnect 5548P: Radius API returned error
Exactly, the first switch working now after the reboot, but the second not. My radius server is a VM running Windows Server 2016 Standard with NPS. Ch.
View ArticleForum Post: Powerconnect 6248 Route Preference
I have about 8 or 9 static routes configured all with preference 1 in my powerconnect 6248. I want to change all of them at once to like 10 or 20 so that I can at least have some wiggle room to add...
View ArticleForum Post: RE: both Core Switches are Master for vlan 10 on N3024F core...
Just to confirm, Is this setup still core one is active for 4 vlans, while core two is active for the other 4 vlans? Core two interface did successfully transition to an up status when issuing the no...
View ArticleForum Post: RE: PowerConnect 5548P: Radius API returned error
Can you check the windows event logs and see if there are any radius errors. httpstechnet.microsoft.com/en-us/library/cc735406(v=ws.10).aspx
View ArticleForum Post: RE: Powerconnect 6248 Route Preference
I don't believe there is a command that will change preference of all the static routes. The quickest method I have used, is to copy the current static routes, modify the metrics in a text editor, and...
View ArticleForum Post: RE: Powerconnect 6248 Route Preference
what command can I run to show the statics routes in the cli?enable show ip route?
View ArticleForum Post: RE: Powerconnect 6248 Route Preference
That will show you the routes in place, but it will not output it in a manner in which you can easily copy and paste. Try this command out # show run | include route.
View ArticleForum Post: RE: Powerconnect 6248 Route Preference
Interesting, well if that is not working, then you may need to just issue the command # show run, and then copy the pertinent route lines from the full config. What firmware is the switch on?
View ArticleForum Post: Unable to configure interface on Dell Powerconnect M6348
I have a task to add more Vlans to an already defined Vlan list on multiple Dell switches. When I go to configure mode, and under the interface, there are no switchport related commands available for...
View ArticleForum Post: RE: Powerconnect 6248 Route Preference
That firmware level is really old. You might consider updating, the newer firmware may add in that pipe functionality. httpdell.to/2tyE9CB Issuing the show run command will provide you with the full...
View ArticleForum Post: RE: Powerconnect 6248 Route Preference
I have the list of all the routes in the show run How do I set it up to be reconfigured with a higher metric? enable config ip route SUBNET ^ MASK ^ NEXT HOP ^ PREFERENCE? EX. ip route 10.10.10.0...
View ArticleForum Post: RE: Unable to configure interface on Dell Powerconnect M6348
Hi, Are you in privileged exec mode? Are the switches stacked?
View ArticleForum Post: RE: PowerConnect 5548P: Radius API returned error
To be sure, I use Wireshark to check. There is no communication between the switch and the server during the port authentication. But the ping works and I see it on Wireshark. Ch.
View ArticleForum Post: RE: Unable to configure interface on Dell Powerconnect M6348
Hi Josh, Yes, I am in privileged mode, and the switch is not stacked. Regards: Thomas
View ArticleForum Post: RE: Unable to configure interface on Dell Powerconnect M6348
I have found out, that the switch is in simple mode. Could be this the reason? What happens if I change the operation mode to normal mode? It is a production switch. Will it cause any impact for the...
View Article
