Forum Post: RE: both Core Switches are Master for vlan 10 on N3024F core...
Admin Mode..................................... Enable Router Checksum Errors......................... 0 Router Version Errors.......................... 0 Router VRID...
View ArticleForum Post: RE: Enable "switchport" command from CLI
And which series of product would have a full functional CLI? I'm looking for a 10G switch with more than 8 ports, which has Cisco style CLI to configure VLAN, L2 access port and trunk ports via CLI....
View ArticleForum Post: RE: Dell Force 10 and Cisco Nexus
Are the interfaces circled in red currently in a LAG? when the interfaces transitioned into a blocking states, was it the individual interfaces or the port channel? Can you post up the config for the...
View ArticleForum Post: RE: Enable "switchport" command from CLI
I do not have any information on the future plans. The N series and the S series switches are full CLI.
View ArticleForum Post: RE: Dell Force 10 and Cisco Nexus
Hi Daniel, Thank you so much again for the follow up, Currently I have not the configuration but it is port channel: Port in hybrid mode switchport vlt-peer-lag port-channel and big MTU 9xxx The Cisco...
View ArticleForum Post: RE: Dell Force 10 and Cisco Nexus
If this is the only connection, then it must be treating this connection as not a port channel. I would double check both the cisco and Nexus to ensure that the port channel is configured correctly.
View ArticleForum Post: RE: both Core Switches are Master for vlan 10 on N3024F core...
The thing that keeps coming up when I research this, is ensuring layer 2 connectivity across that VLAN is good. And check authentication configuration, but you are not using authentication.
View ArticleForum Post: RE: Dell Force 10 and Cisco Nexus
Hi Daniel, just a question, how the STP can be disabled on the interfaces?
View ArticleForum Post: RE: Port Security on 6248's
Action......................................... permit Match All...................................... FALSE Protocol....................................... 255(ip) Source IP...
View ArticleForum Post: RE: Port Security on 6248's
Also i went over your example, the permit first was for local vlan specific hosts, followed by deny to the other vlans and then permit ip any any for unknown hosts.
View ArticleForum Post: RE: Port Security on 6248's
Ok tried it in production again and no go, it's the same switch!
View ArticleForum Post: RE: both Core Switches are Master for vlan 10 on N3024F core...
.but i think its not the ideal or best scinario to have the both are master?? i really serached much and reconfigured from the scratch and tried everything just one vlan that is working fine master and...
View ArticleForum Post: RE: Port Security on 6248's
If the VLAN interfaces do not have an IP address assigned to them, then those VLANs will be in layer 2 mode, and traffic will not be routed by the switch. This means that no ACL would be needed to...
View ArticleForum Post: RE: Dell Force 10 and Cisco Nexus
Disabling spanning tree is not recommended. I am not seeing a method of disabling per interface, just globally. httpdell.to/2r0TLlF
View ArticleForum Post: RE: Dell Force 10 and Cisco Nexus
Thank you, You are right, I was thinking the same about STP, do you have the recommended configuration for LACP under the Dell F10 interfaces connected to Cisco? or any documentation? Thank you again
View ArticleForum Post: RE: Port Security on 6248's
It was actually the same in both scenarios. So assigning an ip to a vlan makes a difference? Routing is still being done by the Sophia though so the vlans will still communicate.
View ArticleForum Post: 6224 not registering MAC's?
I have two R710's running vmware 6. I'm trying to set up a standard switch on each host to do vmotion on a separate vlan. I have another set up for iscsi traffic that seems to be working fine, on a...
View ArticleForum Post: RE: Port Security on 6248's
configure vlan database vlan 2,8,40,254-255 vlan routing 2 1 vlan routing 40 2 vlan routing 8 3 exit hostname "wanipswitch" stack member 1 2 exit ip address dhcp ip domain-name xxxxxx access-list...
View ArticleForum Post: PowerConnect VLAN Setting
What I would like is to setup ports on the PowerConnect correctly in order to get the tagged traffic from the AP through the PowerConnect and on to the router. (and on to the internet)
View Article