Forum Post: RE: DELL S6000 and GVRP
Use the GVRP registration command. Set a forbidden VLAN. Page 352
View ArticleForum Post: Dell N3000 Series LLDP neighbor ID
The N3024, lldp sends the "system ID" or "neighbor ID" as the mac of the switch to my other lldp enabled devices. Or at least that is what is received. Can I specify what is sent as the lldp ID or...
View ArticleForum Post: RE: MXL 10/40GbE blade switch - What is the latest firmware, and...
Are you entering the service tag? Force10 switches require service tag or account verification for updates. If it still is not showing up with the service tag you may have to use the Force10 site with...
View ArticleForum Post: RE: MXL 10/40GbE blade switch - What is the latest firmware, and...
I have added my service tags, and still there is no mention of the FTOS on this support site. I believe I am going to have to open an actual support incident to get any invformation. Oh the needless...
View ArticleForum Post: RE: MXL 10/40GbE blade switch - What is the latest firmware, and...
This is getting truly frustrating now. The Force10 MXL switch is the cutting edge blade interconnect and costs about 11K per machine and I have 4 of these. I cannot find support even with the service...
View ArticleForum Post: RE: MXL 10/40GbE blade switch - What is the latest firmware, and...
Apparently my sales guy forgot to add the M-Sereis switches to my Force10 support site profile. This is unfortunate because it has been over a year since I purchased the 2nd stack of these and he never...
View ArticleForum Post: RE: Dell N3000 Series LLDP neighbor ID
Hi, There is not a way to change the system ID. You can change what additional information is sent though. Page 844
View ArticleForum Post: powerconnect 8024F and 5524 operating at 100Mbps
I'm not a networking guy and we outsource our networking to consultants who have not been available to help much, so I'm hoping I can find some guidance here. Our configuration is as follows: Two 8024F...
View ArticleForum Post: RE: DELL S6000 and GVRP
What about N series switches? I cannot find in manual.
View ArticleForum Post: Help connect Cisco4510r+e and Dell PowerEdge M1000e by 10GB
At the Cisco4510r+e connection (WS-X4712-SFP+E card) the SFP-H10GB-CU5M and Dell PowerEdge M1000e cable (Powerconect m8024 card) there is no link At the Cisco4510r+e connection (WS-X4712-SFP+E card) of...
View ArticleForum Post: switch fabric capacity
According to the spec sheet, the dell S3048-ON switch fabric capacity is 260Gbps, how to caculate the switch fabric? S3048-ON has 48 GbE and 4 SFP+. Can someone answer the question? cheers.
View ArticleForum Post: RE: Change MTU to lag members
What model switch are you using? If you are changing it on both the physical and the port channel, change it on the physical first, however you may only need to change it on the port channel.
View ArticleForum Post: RE: powerconnect 8024F and 5524 operating at 100Mbps
Hi, Are the link lights on the switch green or amber? Page 40 Are these long cabling runs? If you bypass the seitches and connect a laptop right to the devices do they operate at gigabit speeds?
View ArticleForum Post: RE: switch fabric capacity
It is the maximum potential throughput the switch backplane is able to handle. Broadcast and multicast traffic can potentially have 1 port that is putting more than 1Gb of traffic onto the fabric.
View ArticleForum Post: RE: powerconnect 8024F and 5524 operating at 100Mbps
Thanks for your reply. These are not long cable runs by any stretch - all of the equipment is mounted in the same cage, so the longest run would be around 3 feet. Since my initial post I uncorvered...
View ArticleForum Post: RE: DELL S6000 and GVRP
In N series switches cannot forbid selected VLAN's How to do the same on N series switches like on S series: #gvrp registration fixed 34,35 #gvrp registration forbidden 45,46 Missing theses commands on...
View ArticleForum Post: RE: Help connect Cisco4510r+e and Dell PowerEdge M1000e by 10GB
Powerconect m8024 m8024 version image 4.1.0.6 cisco 4510r+e version Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSAL-M), Version 03.04.00.SG RELEASE SOFTWARE (fc3) DATA from tranceiver dell...
View ArticleForum Post: X-Series DHCP Server settings only allow one DNS server?!
the Domain Name Server field (which the online Help says corresponds to DHCP option 6) only accepts one IP address. All of the specifications I've seen for option 6 (and every other DHCP server I've...
View Article