Forum Post: RE: Dell PowerConnect 5548P VLANS for VOIP
VIOP sever is an embedded card on an AVAYA IPO system 10.3.30.10 and it hands out DHCP 10.3.30.200-254
View ArticleForum Post: RE: Dell PowerConnect 5548P VLANS for VOIP
Thanks for that info. More than likely, by default that device is going to send and receive untagged packets. Unless there is a setting on the server itself that has been change to have the server send...
View ArticleForum Post: RE: PowerConnect 2824 Vlan Problem
Hi, Thank you for the help. I am hesitant to do this right away. Will it affect the internet? As some of our offices are connected to this switch. Regards, Dang
View ArticleForum Post: RE: PowerConnect 2824 Vlan Problem
Assigning an IP address to a VLAN should not cause any downtime. If you want to be extra cautious, then perform these steps during non peak hours.
View ArticleForum Post: RE: Handling multi-tenancy
Private VLANs may be able to help you achieve this goal. Here is a white paper that covers private VLANs, and includes some examples. httpdell.to/2ev58uq
View ArticleForum Post: RE: Configuring PowerEdge M I/O Aggregator in PMUX mode - help...
Here is a good white paper that covers VoIP deployment on the N-series. It has some config example you can reference. httpdell.to/1Ghildb I don’t see anything wrong with the commands you ran. Is the...
View ArticleForum Post: RE: Dell PowerConnect OIDs
Have you tried these OIDs out yet? Temperature OID .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.2 .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.3 .1.3.6.1.4.1.674.10895.5000.2.6132.1.1.43.1.8.1.4
View ArticleForum Post: Setting up VLAN with Dell 3548p switch
I am currently working on a project to provide the office I support with wireless connectivity that allows the users to also be able to access network folders and servers, as if they were connected to...
View ArticleForum Post: LAG Setup with multiple Vlans
In a LAG configuration, in order to pass vlan traffic, the port channel should be setup in Trunk or General mode while the physical ports in access mode or both should be setup in Trunk or General mode?
View ArticleForum Post: RE: Configuring PowerEdge M I/O Aggregator in PMUX mode - help...
DELL#show running-config Current Configuration ... ! Version 9.11(0.0P8) ! Last configuration change at Wed Mar 22 14:21:58 2017 by default ! Startup-config last updated at Wed Mar 22 14:23:44 2017 by...
View ArticleForum Post: RE: Setting up VLAN with Dell 3548p switch
It sounds like the wireless clients need access to the same resources that the wired clients use. Is there a need for these wireless clients to be on a different VLAN? If not, then plug the APs into...
View ArticleForum Post: RE: Configuring PowerEdge M I/O Aggregator in PMUX mode - help...
There is no need to configure tlv for switch to switch connections. I am not seeing anything wrong with the configuration you posted. I would double check and confirm how the Cisco switch is...
View ArticleForum Post: RE: LAG Setup with multiple Vlans
Once a port is placed in a port-channel, the physical interface only follows the commands given to the port-channel. The Trunk configuration only needs to be placed on the port-channel interface.
View ArticleForum Post: RE: Dell PowerConnect 5548P VLANS for VOIP
I think I've narrowed down the issue. I really need to have all DHCP on one server so I opened up Port 1 for VLAN 30 again so DCHP from the Windows server comes through. (testing prior showed I could...
View ArticleForum Post: RE: Dell PowerConnect 5548P VLANS for VOIP
The phone on port 19 finally showed up on the DHCP server in the wrong VLAN50 So the config on port 20 is almost right. I'll try removing VLAN 30 and Enable Voice VLAN on it. Hopefully this will be the...
View ArticleForum Post: Dell N4032F Switch Startup
Today ı was triying to startup 2 Dell N4032F switch.However when ı plug in the all psu cables,I realized that switch didn't start and switch green led was blinking. I would like to make sure that...
View ArticleForum Post: RE: Dell N4032F Switch Startup
Are you trying to stack two switches? Make sure the ports used for stacking are in stack mode. Which green LED was blinking, was it the Diag LED on the back of the switch, or other LED?
View ArticleForum Post: RE: Configuring PowerEdge M I/O Aggregator in PMUX mode - help...
The interfaces in port-channel are not in sequence do we need them in sequence ? for example the port-channel are configured with 0/34-35,0-37 ports because 36 port is not connected on the chassis.
View ArticleForum Post: RE: Dell N4032F Switch Startup
This is unconfigured switchs.I mean new one.Today has been unboxed.Led was blinking on the top of the power supply unit.I think just power led not diag.(Back of the switch) That's why ı confused....
View ArticleForum Post: RE: Dell PowerConnect 5548P VLANS for VOIP
If the request came in on VLAN 50, that means the phone is not negotiating with the switch and being placed on VLAN 30. That white paper indicated that Voice VLAN needed to be removed form the Trunk.
View Article